![icom ic-7300 rs-ba1 icom ic-7300 rs-ba1](https://www.icom-france.com/images/1280x1280/produit/me-cffffff/RS-BA1_RC-28.jpg)
The exact capabilities of this device varies by radio model.Ĭopyright 2019-2021, Universal Radio, Inc.
#Icom ic 7300 rs ba1 software#
This software is designed to operate with Windows® 7, Windows® 8.1 and Windows® 10 on a PC with 1.8 GHz processor or better, 150 Mb HD, 1024x768 resolution. The IC-9700 can be connected to a PC via a USB cable and the input/output audio signal and CI-V command is sent through the USB cable. Remote control software provides a user interface, similar to the radio's front panel, and allows you to control the radio from a remote location. System configuration software sets up IP address, audio sampling rate and other settings.Ģ. The RS-BA1 Windows® CD consists of two component software applications:ġ.
#Icom ic 7300 rs ba1 trial#
Download Trial Icom IC-7300 Icom IC-7610 SDRPlay. Shown above in use with a dual-receive transceiver. Win4IcomSuite for Icom Radios eine Alternative zur Icom Software RS-BA1/RS-BA2 Remote Control. The RS-BA1 Version 2 can also still be used with single-receiver transceivers. The RS-BA1 Version 2 can also enlarge the panel size (normal or large is selectable), buttons added, clickable indicators to change settings, SUB dial added and RIT tuning knob & TX functions added. With the RS-BA1 Version 2, you can use the dual watch operation and spectrum scopes with waterfall function as well as observe the MAIN and SUB spectrum scopes. Anstatt das empfangene Signal wie bei einem traditionellen Empfänger zunächst herunter zu mischen wird also mit einem leistungsfähigen Analog. Das besondere an diesem Gerät ist, dass das HF-Signal unmittelbar nach dem Bandfilter digitalisiert wird. The S-Meter and SWR can even be observed. Mit dem IC-7300 stellt Icom als Erster der drei großen japanischen Hersteller einen echten SDR Transceiver vor (Software Defined Radio). Low voice latency (caused by the RS-BA1) provides the same operational experience as using an actual radio. Both radios were tested on-air in my station, with the Yaesu Quadra amplifier and Cushcraft R8 antenna, and are now installed in the shack. The USB3 I/Q port was not yet functional when the test suite was run, but was tested functionally when Firmware V1.20 was released (Aug. Most functions and modes of your Icom compatible transceiver can be controlled, including interference rejection functions and IF filter settings. The IC-7610 LAN port was tested functionally in my station with the Icom RS-BA1 suite. I may revisit this review once I have time to use it more.The Icom RS-BA1 v2 IP Remote Control Software allows you to use an Icom compatible radio installed in another room using your home network or even from a remote location over the Internet.
![icom ic-7300 rs-ba1 icom ic-7300 rs-ba1](https://klop.solutions/wp-content/uploads/2017/08/Client-Radio-Connected.png)
Also could not import from Excel my memory setup. It cannot seem to read what I had programmed into the radio with RT Systems software.
![icom ic-7300 rs-ba1 icom ic-7300 rs-ba1](https://i1.wp.com/swling.com/blog/wp-content/uploads/2021/02/IC-9700.jpg)
So I'm still trying to sort that out.Īnother issue is the memory functions. The button to key the mic works, but you can talk all day long and it won't send. One item I don't like is EVERY time I connect the radio, the software shuts the mic input off. Running the program is not super difficult, but not everything is intuitive. Once that was set, it connects every time now. The initial setup in Win10 was easy to install, but connecting to the radio took some work and required getting into the Device Manager console to set the COM port. It has not been the easiest computer controller software to use, but not the hardest either. I bought this software when I bought my Icom IC-7100. I only have a little experience with computer control of the radio. Mainly using this on 6 and 10 meter right now.ī. I'm new to HF radio's as I am still a Tech class operator.